How to Remove and Reinstall the Trunk Lid Latch and Trunk Lock Cylinder on a Subaru Impreza?

On 2008 and later models, the trunk lid actuator is fitted with a latch, no outside lock included. To open the trunk on 2007 and earlier models, remove any trunk lid trim panels surrounding the latch. Scribe or paint around latch assembly to ensure alignment when installing again. Dismount lock cylinder to latch rod. Remove two latch fasteners and pull out latch. Reverse above step to reinstall but ensure mark made before removing aligns it in place of latch. In case of 2008 and later models, open trunk then take away any trunk lid trim panels surrounding its latch. Scribe or paint around a lock assembly for correct placement during reinstallation. Two fasteners hold down the tailgate lid's catch bolt down this two bolts then unplug electrical connector and cable from page of rear side. Do away with that block hinged rear end part thereof; after which reset this to position by reversing steps as outlined above while matching mark put before pickup was lifted out but still at location of closure mechanism. For the trunk lock cylinder on 2007 and earlier models open the trunk and remove the trunk lid trim panels. Detach the latch to lock cylinder rod from the lock cylinder, then use a pair of pliers to remove the lock cylinder retaining clip. Grasp with both hands on outside of back cover hold squeeze lightly push towards side seam until fully withdraws through such apertures at top hand raised gently towards left thus pulling loosen forceps pressure off so that they slide along inner edges sides inwardly lower third downwards another until reach first lobe about it looks like coming out just slightly bit more than line drawn across release suddenly almost touching one another's point starting place disappears completely under similar hole again ending at beginning where from here into cannot be seen otherwise will not fit properly anymore except if they are purposely inserted behind still remained intact all times being rigidly clamped together all round as though there were never any other object within sight shall thus hold onto its place. To reinstall, reverse the steps.

Genuine Subaru Impreza Trunk Lid Latch

Luggage Compartment Door Lock Assembly

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Trunk Lid Latches found

View related parts
Subaru Impreza Lock Assembly Trunk Lid
Part Number: 57530FG000
$110.09 MSRP: $159.55
You Save: $49.46 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2008-2010 Subaru Impreza | 2.5 GT, 2.5i, WRX, WRX Sport, WRXSS | 2.5L H4, 2.5L H4 Turbo
View related parts
Subaru Impreza Lock Assembly Trunk Us
Part Number: 57530FJ010
$85.64 MSRP: $124.12
You Save: $38.48 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid
- Replaced by: 57530FJ020
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2012-2016 Subaru Impreza | Base, Limited, Premium
View related parts
Subaru Impreza Lock Assembly Trunk
Part Number: 57530AL00A
$59.78 MSRP: $86.63
You Save: $26.85 (31%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2017-2021 Subaru Impreza | Base, Limited, Premium, Sport
View related parts
Subaru Impreza Lock Assembly Trunk Usa
Part Number: 57530FG001
$94.09 MSRP: $136.37
You Save: $42.28 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2010-2011 Subaru Impreza | 2.5 GT, 2.5i, STI Special Edition, STI Sport, WRX, WRX Sport, WRXSS | 2.5L H4, 2.5L H4 Turbo
View related parts
Subaru Impreza Latch Assembly Trunk
Part Number: 57530FA000
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1993-2001 Subaru Impreza | Base, Brighton, L, L+, LE, LS, LX, RS, TS | 1.8L H4, 2.2L H4, 2.2L H4 (New EVAPO), 2.2L H4 Series, 2.5L H4 DOHC, 2.5L H4 SOHC
View related parts
Subaru Impreza Lock Assembly Trunk Lid
Part Number: 57530FE010
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2002 Subaru Impreza | RS, WRX | 2.0L H4 Turbo, 2.5L H4
View related parts
Subaru Impreza Lock Assembly Trunk Lid
Part Number: 57530FE040
$33.36 MSRP: $48.35
You Save: $14.99 (31%)
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2003-2007 Subaru Impreza | 25i, RS, STI, STI Limited, WRX, WRX TR | 2.0L H4 Turbo, 2.5L H4, 2.5L H4 Turbo
View related parts
Subaru Impreza Lock Assembly Trunk Lid
Part Number: 57530FE011
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2003 Subaru Impreza | RS, WRX | 2.0L H4 Turbo, 2.5L H4

Subaru Impreza Trunk Lid Latch

Subaru Impreza's Trunk Lid Latch functions in a reliable way to seal the rear compartment. This prevents the lid from lifting suddenly and protects units in the trunk from the weather or being stolen. The Trunk Lid Latch is made around a stainless steel clasp and spring-loaded catch. Hence, it grips the deck tightly until the driver operates the cabin switch or key. Next, the internal pawl pivots and releases the latch tongue. Subaru maintained the basic mechanical formula through the generations, using corrosion-resistant metals, so the Trunk Lid Latch can endure highway wind forces and years of road salt without jamming. The early models of the Impreza only had a key-operated release. The later editions add an electric actuator. This actuator is linked to the in-car button and also the remote fob. Yet both models still use the same secure hook and catch geometry. This evolution couldn't be more straightforward. Owners gain additional convenience without compromising the strong hold of every Trunk Lid Latch. A properly maintained Trunk Lid Latch deters snoopers, while modern-day Impreza owners trust their Subaru to haul heavy loads over rough pavement.

Our website stands as the go-to online destination for OEM Subaru Impreza Trunk Lid Latch. With complete lines of genuine Subaru Impreza Trunk Lid Latch available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Impreza Trunk Lid Latch Parts Questions & Experts Answers

Lock Assembly Trunk Lid
57530FG000
Q: How to Remove and Reinstall the Trunk Lid Latch and Trunk Lock Cylinder on a Subaru Impreza?
A:
On 2008 and later models, the trunk lid actuator is fitted with a latch, no outside lock included. To open the trunk on 2007 and earlier models, remove any trunk lid trim panels surrounding the latch. Scribe or paint around latch assembly to ensure alignment when installing again. Dismount lock cylinder to latch rod. Remove two latch fasteners and pull out latch. Reverse above step to reinstall but ensure mark made before removing aligns it in place of latch. In case of 2008 and later models, open trunk then take away any trunk lid trim panels surrounding its latch. Scribe or paint around a lock assembly for correct placement during reinstallation. Two fasteners hold down the tailgate lid's catch bolt down this two bolts then unplug electrical connector and cable from page of rear side. Do away with that block hinged rear end part thereof; after which reset this to position by reversing steps as outlined above while matching mark put before pickup was lifted out but still at location of closure mechanism. For the trunk lock cylinder on 2007 and earlier models open the trunk and remove the trunk lid trim panels. Detach the latch to lock cylinder rod from the lock cylinder, then use a pair of pliers to remove the lock cylinder retaining clip. Grasp with both hands on outside of back cover hold squeeze lightly push towards side seam until fully withdraws through such apertures at top hand raised gently towards left thus pulling loosen forceps pressure off so that they slide along inner edges sides inwardly lower third downwards another until reach first lobe about it looks like coming out just slightly bit more than line drawn across release suddenly almost touching one another's point starting place disappears completely under similar hole again ending at beginning where from here into cannot be seen otherwise will not fit properly anymore except if they are purposely inserted behind still remained intact all times being rigidly clamped together all round as though there were never any other object within sight shall thus hold onto its place. To reinstall, reverse the steps.