How Do Coil Springs and Shock Absorbers Affect the Disassembly and Reassembly of Strut Assemblies on a Subaru Legacy?

For this procedure, a spring compressor is needed, and these can be hired daily from most auto parts stores or equipment yards. If the struts or coil springs show signs of wear, for example, leaking fluid or cracks take all into consideration, before any job commences, the strut/shock absorber assembly cannot be repaired, and will have to be replaced under the said circumstances. Rather than purchasing strut assemblies with springs, it can be ordered on exchange basis, or wanted, thus, it is recommended to compare the cost and availability of the stated parts before disassembling the vehicle further. First, disengage the strut and spring assembly and then it is to be installed on a wooden Shaped Vise Cover that prevents the denting of the steel but must be tightened not very thoroughly. Mount the spring compressor in a proper manner as described in the direction of the spring compressor and compress the spring up to a stage which there is no pressure left on the upper spring seat , this can be indicated by a rocking movement of the spring. Further, undo the nut on the damper shaft using a socket wrench to eventually pull off the upper Strut mount inclusive of the spacer meanwhile checking of the bearing to see that it rotates freely then replace the strut mount in case it is worn out. The upper spring seat rubber seat as well as dust cover have to be dismantled and one has to inspect the surfaces to establish whether they are worn out or not. In lifting the compressed spring back from the assembly, ensure that the two ends do not point toward you and after putting it, ensure that it is safe. Slide off the rubber bumper from the damper shaft and has to check for the worn out rubber bumper and replace it if so. To assembled back again it is suggested to use new self-locking nut. Twist the damper rod repeatedly until it is possible to compress and fully retract it, this is in a bid to clear any air trapped in the component, then to set it free, pull it to its full size and fit the rubber bumper. The first step is to locate the coil spring on the lower insulator and engaging the end of the spring with the recessed portion next is installing the dust cover, rubber seat, and the upper spring seat. Last of it, fit the spacer and upper strut mount and fasten it with a new self locking nut tightened to the prescribed torque and finally reassemble the strut/coil spring.

Genuine Subaru Legacy Coil Springs

Strut Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

185 Coil Springs found

View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AC330
$50.98 MSRP: $73.88
You Save: $22.90 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1998 Subaru Legacy | Out Back | 2.5L H4
View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AC320
$50.98 MSRP: $73.88
You Save: $22.90 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1999 Subaru Legacy | Out Back | 2.5L H4
View related parts
Subaru Legacy Rear Coil Spring
Part Number: 20380AG11A
$51.60 MSRP: $74.78
You Save: $23.18 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Rear; Coil Spring, Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2005-2009 Subaru Legacy | 2.5i, 2.5i Limited, 3.0R, 3.0R Limited, 3.0R LL-Bean, Base, GT, GT Limited, XT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Legacy Rear Coil Spring
Part Number: 20380AE23A
$55.23 MSRP: $80.05
You Save: $24.82 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Rear; Coil Spring, Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2004 Subaru Legacy | Base, Cold Weather, Flat6-S, Limited | 2.5L H4, 3.0L H6
View related parts
Subaru Legacy Front Suspension-Coil Spring
Part Number: 20330AL01A
$36.01 MSRP: $52.18
You Save: $16.17 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2019 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport | 2.5L H4
View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AE22A
$38.23 MSRP: $55.40
You Save: $17.17 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2002 Subaru Legacy | Base, Cold Weather, Limited, SUS Limited | 2.5L H4
View related parts
Subaru Legacy Rear Suspension-Coil Spring
Part Number: 20380AL00A
$37.20 MSRP: $53.92
You Save: $16.72 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Rear; Coil Spring, Spring
- Position: Rear
- Replaced by: 20380AL00B
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2017 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport | 2.5L H4
View related parts
Subaru Legacy Rear Coil Spring
Part Number: 20380AL23A
$36.35 MSRP: $52.68
You Save: $16.33 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2019 Subaru Legacy | 3.6R Limited, 3.6R Premium, 3.6R Touring | 3.6L H6
View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AL06A
$36.25 MSRP: $52.53
You Save: $16.28 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2019 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Touring | 2.5L H4
View related parts
Subaru Legacy Coil Spring
Part Number: 20330AN02A
$46.02 MSRP: $66.70
You Save: $20.68 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring F
- Position: Front
- Replaced by: 20330AN02B
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2020-2021 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Touring | 2.5L H4 DI
View related parts
Subaru Legacy Rear Coil Spring
Part Number: 20380AL22A
$35.93 MSRP: $52.07
You Save: $16.14 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2019 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Touring | 2.5L H4
View related parts
Subaru Legacy Coil Spring
Part Number: 20380AN00A
$25.91 MSRP: $37.55
You Save: $11.64 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring R
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2020-2021 Subaru Legacy | 2.4R Limited, 2.4R Touring, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring | 2.4L H4 DIT, 2.5L H4 DI
View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AC310
$50.98 MSRP: $73.88
You Save: $22.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1999 Subaru Legacy | Out Back | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Legacy Coil Spring
Part Number: 20380AN01A
$28.58 MSRP: $41.42
You Save: $12.84 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring R
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2020-2021 Subaru Legacy | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Touring | 2.5L H4 DI
View related parts
Subaru Legacy Front Suspension-Coil Spring
Part Number: 20330AL07A
$36.71 MSRP: $53.20
You Save: $16.49 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2019 Subaru Legacy | 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 3.6L H6
View related parts
Subaru Legacy Front Suspension-Coil Spring
Part Number: 20330AL02A
$36.41 MSRP: $52.77
You Save: $16.36 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2019 Subaru Legacy | 3.6R, 3.6R Limited, 3.6R Premium | 3.6L H6
View related parts
Subaru Legacy Rear Suspension-Coil Spring
Part Number: 20380AL05A
$32.52 MSRP: $47.13
You Save: $14.61 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Rear; Coil Spring, Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2017 Subaru Legacy | 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 3.6L H6
View related parts
Subaru Legacy Front Coil Spring
Part Number: 20330AC300
$50.98 MSRP: $73.88
You Save: $22.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring-Front; Coil Spring, Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1999 Subaru Legacy | Out Back | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Legacy Coil Spring
Part Number: 20380AN02A
$28.58 MSRP: $41.42
You Save: $12.84 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring R
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2020-2021 Subaru Legacy | 2.4R F/R-O, 2.4R Limited, 2.4R Touring | 2.4L H4 DIT
View related parts
Subaru Legacy Rear Coil Spring
Part Number: 20380AL21A
$34.05 MSRP: $49.35
You Save: $15.30 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Spring Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2019 Subaru Legacy | 3.6R Limited | 3.6L H6

| Page 1 of 10 |Next >

1-20 of 185 Results

Subaru Legacy Coil Springs

Coil Springs of Subaru Legacy help support the vehicle's weight and keep it level while also absorbing the shock from bumps on the road and keeping the tires in contact with the road. Coil Springs compress and extend as the wheels travel over an uneven surface. They provide a balance of ride comfort and handling stability while also preventing bottoming or excessive body roll. Properly working Coil Springs uphold ride height in the Subaru Legacy suspension, promoting accurate wheel alignment. In turn, this allows for even tire wear. The rear Coil Springs may be sagging or harsh if the vehicle is old or has been subject to modified suspension setups. The Subaru midsize model offers Legacy owners replacement Coil Springs that are offered in OEM spec form to restore stock characteristics, variable rate forms that start soft and become firmer under load, linear rate springs with constant stiffness, and dual rate designs that alternate between two set rates. Each style of Coil Springs is defined by free length and spring rate. This gives the Legacy a composed and comfortable feel while retaining Subaru ride quality.

Our website stands as the go-to online destination for OEM Subaru Legacy Coil Springs. With complete lines of genuine Subaru Legacy Coil Springs available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Legacy Coil Springs Parts Questions & Experts Answers

Front Coil Spring
20330AG14A
Q:
How Do Coil Springs and Shock Absorbers Affect the Disassembly and Reassembly of Strut Assemblies on a Subaru Legacy?
Posted by Sarah S.
A:
For this procedure, a spring compressor is needed, and these can be hired daily from most auto parts stores or equipment yards. If the struts or coil springs show signs of wear, for example, leaking fluid or cracks take all into consideration, before any job commences, the strut/shock absorber assembly cannot be repaired, and will have to be replaced under the said circumstances. Rather than purchasing strut assemblies with springs, it can be ordered on exchange basis, or wanted, thus, it is recommended to compare the cost and availability of the stated parts before disassembling the vehicle further. First, disengage the strut and spring assembly and then it is to be installed on a wooden Shaped Vise Cover that prevents the denting of the steel but must be tightened not very thoroughly. Mount the spring compressor in a proper manner as described in the direction of the spring compressor and compress the spring up to a stage which there is no pressure left on the upper spring seat , this can be indicated by a rocking movement of the spring. Further, undo the nut on the damper shaft using a socket wrench to eventually pull off the upper Strut mount inclusive of the spacer meanwhile checking of the bearing to see that it rotates freely then replace the strut mount in case it is worn out. The upper spring seat rubber seat as well as dust cover have to be dismantled and one has to inspect the surfaces to establish whether they are worn out or not. In lifting the compressed spring back from the assembly, ensure that the two ends do not point toward you and after putting it, ensure that it is safe. Slide off the rubber bumper from the damper shaft and has to check for the worn out rubber bumper and replace it if so. To assembled back again it is suggested to use new self-locking nut. Twist the damper rod repeatedly until it is possible to compress and fully retract it, this is in a bid to clear any air trapped in the component, then to set it free, pull it to its full size and fit the rubber bumper. The first step is to locate the coil spring on the lower insulator and engaging the end of the spring with the recessed portion next is installing the dust cover, rubber seat, and the upper spring seat. Last of it, fit the spacer and upper strut mount and fasten it with a new self locking nut tightened to the prescribed torque and finally reassemble the strut/coil spring.
Answered by Subaru Parts Specialist William / May 23, 2023