How to remove and reinstall the Trunk Lid Latch and Trunk Lock Cylinder on a Subaru Outback?

On 2008 and later models, the trunk lid actuator is fitted with a latch, no outside lock included. To open the trunk on 2007 and earlier models, remove any trunk lid trim panels surrounding the latch. Scribe or paint around latch assembly to ensure alignment when installing again. Dismount lock cylinder to latch rod. Remove two latch fasteners and pull out latch. Reverse above step to reinstall but ensure mark made before removing aligns it in place of latch. In case of 2008 and later models, open trunk then take away any trunk lid trim panels surrounding its latch. Scribe or paint around a lock assembly for correct placement during reinstallation. Two fasteners hold down the tailgate lid's catch bolt down this two bolts then unplug electrical connector and cable from page of rear side. Do away with that block hinged rear end part thereof; after which reset this to position by reversing steps as outlined above while matching mark put before pickup was lifted out but still at location of closure mechanism. For the trunk lock cylinder on 2007 and earlier models open the trunk and remove the trunk lid trim panels. Detach the latch to lock cylinder rod from the lock cylinder, then use a pair of pliers to remove the lock cylinder retaining clip. Grasp with both hands on outside of back cover hold squeeze lightly push towards side seam until fully withdraws through such apertures at top hand raised gently towards left thus pulling loosen forceps pressure off so that they slide along inner edges sides inwardly lower third downwards another until reach first lobe about it looks like coming out just slightly bit more than line drawn across release suddenly almost touching one another's point starting place disappears completely under similar hole again ending at beginning where from here into cannot be seen otherwise will not fit properly anymore except if they are purposely inserted behind still remained intact all times being rigidly clamped together all round as though there were never any other object within sight shall thus hold onto its place. To reinstall, reverse the steps.

Genuine Subaru Outback Trunk Lid Latch

Luggage Compartment Door Lock Assembly

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Trunk Lid Latches found

View related parts
Subaru Outback Lock Assembly Trunk Lid
Part Number: 57530AG010
$92.77 MSRP: $134.45
You Save: $41.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2005-2009 Subaru Outback | 2.5i, 2.5i Base, 2.5i Limited, 3.0R, 3.0R Limited, 3.0R LL-Bean, GT, GT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Lock Assembly Trunk
Part Number: 57530AJ00A
$46.18 MSRP: $66.93
You Save: $20.75 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2010-2014 Subaru Outback | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 3.6R, 3.6R Limited, 3.6R Premium | 2.5L H4 DOHC, 2.5L H4 SOHC, 2.5L H4 Turbo, 3.6L H6
View related parts
Subaru Outback Lock Assembly Trunk
Part Number: 57530AL00A
$59.78 MSRP: $86.63
You Save: $26.85 (31%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2021 Subaru Outback | 2.4R Limited, 2.4R Touring, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium | 2.4L H4 DIT, 2.5L H4, 2.5L H4 DI, 3.6L H6
View related parts
Subaru Outback Lock Trunk
Part Number: 57530AG060
$92.38 MSRP: $133.88
You Save: $41.50 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2009 Subaru Outback | 2.5i, 2.5i Base, 2.5i Limited, 3.0R, 3.0R Limited, GT, GT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Lock Assembly Trunk
Part Number: 57530AC010
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1998 Subaru Outback | GT, LS, LS-I | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Outback Lock Assembly Trunk
Part Number: 57530AC000
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1999 Subaru Outback | GT, L, LS, LS-I, SUS | 2.2L H4 , 2.2L H4 (New EVAPO), 2.2L H4 Series, 2.5L H4
View related parts
Subaru Outback Lock Assembly (Trunk)
Part Number: 57530AE00B
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2001-2002 Subaru Outback | GT, L, SUS Flat6, SUS Limited | 2.5L H4, 3.0L H6
View related parts
Subaru Outback Lock Assembly (Trunk)
Part Number: 57530AE00C
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2002-2004 Subaru Outback | GT, L, L-S, SUS Flat6, SUS Limited | 2.5L H4, 3.0L H6
View related parts
Subaru Outback Lock Assembly Trunk
Part Number: 57530AE00A
Product Specifications
- Other Name: Lock Assembly-Trunk Lid; Lock
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2001 Subaru Outback | GT, L, SUS Limited | 2.5L H4

Subaru Outback Trunk Lid Latch

Subaru Outback Trunk Lid Latch allows the rear storage door to shut and keep cargo safe while driving. It also will not allow the trunk lid to come open accidentally. The stainless steel components of the Trunk Lid Latch prevent the lid from coming off due to wind pressure or vibration. The lid will be locked until the user presses the button on the key or the key fob. The early generations had a simple mechanical pawl that was activated by a cabin lever. Later models adopted an electric Trunk Lid Latch that is linked to the central locking. Hence, one press secures both doors and the hatch. The two styles utilize a spring-loaded Trunk Lid Latch catch that bites into a fixed striker to clamp the lid tight. A faulty Subaru Trunk Lid Latch can result in the lid swinging open, which can cause you to lose your gear and invite theft. Therefore, it is absolutely essential that yours operate dependably. For camping gear or groceries, Subaru Outback drivers trust the refined latch to keep their versatile Outback ready for the next adventure.

Our website stands as the go-to online destination for OEM Subaru Outback Trunk Lid Latch. With complete lines of genuine Subaru Outback Trunk Lid Latch available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Outback Trunk Lid Latch Parts Questions & Experts Answers

Lock Assembly Trunk
57530AJ00A
Q:
How to remove and reinstall the Trunk Lid Latch and Trunk Lock Cylinder on a Subaru Outback?
Posted by Michelle K.
A:
On 2008 and later models, the trunk lid actuator is fitted with a latch, no outside lock included. To open the trunk on 2007 and earlier models, remove any trunk lid trim panels surrounding the latch. Scribe or paint around latch assembly to ensure alignment when installing again. Dismount lock cylinder to latch rod. Remove two latch fasteners and pull out latch. Reverse above step to reinstall but ensure mark made before removing aligns it in place of latch. In case of 2008 and later models, open trunk then take away any trunk lid trim panels surrounding its latch. Scribe or paint around a lock assembly for correct placement during reinstallation. Two fasteners hold down the tailgate lid's catch bolt down this two bolts then unplug electrical connector and cable from page of rear side. Do away with that block hinged rear end part thereof; after which reset this to position by reversing steps as outlined above while matching mark put before pickup was lifted out but still at location of closure mechanism. For the trunk lock cylinder on 2007 and earlier models open the trunk and remove the trunk lid trim panels. Detach the latch to lock cylinder rod from the lock cylinder, then use a pair of pliers to remove the lock cylinder retaining clip. Grasp with both hands on outside of back cover hold squeeze lightly push towards side seam until fully withdraws through such apertures at top hand raised gently towards left thus pulling loosen forceps pressure off so that they slide along inner edges sides inwardly lower third downwards another until reach first lobe about it looks like coming out just slightly bit more than line drawn across release suddenly almost touching one another's point starting place disappears completely under similar hole again ending at beginning where from here into cannot be seen otherwise will not fit properly anymore except if they are purposely inserted behind still remained intact all times being rigidly clamped together all round as though there were never any other object within sight shall thus hold onto its place. To reinstall, reverse the steps.
Answered by Subaru Parts Specialist Gary / Jul 13, 2026