How to Change the Engine Oil Filter on a Subaru Legacy?

Oil changes should be regular if one is to care for the engine of his/her car because after a while, the oil in it becomes diluted and contaminated, causing premature wear out of the engine. When changing the oil filter and oil on your vehicle make sure that you have drain pan, rubber gloves, breaker bar/sockets and filter wrench available. You can also use rags or newspapers to wipe up spills. Hoist, ramps or jacks will allow you get under your car more easily. Find out where it is by draining some warm-up before removing an oil plug from an engine. In order to avoid getting a bad reading put the car on a level ground surface, heat up the engine and then remove the oil filler cap. Jack-up a vehicle with a floor jack; place drain pan beneath an oil plug; take off a plug; wait till all old oil has been drained out; check whether there are metal shavings in it; clean them away from an opening by wiping off all smudges remained there before reinstalling that plug carefully into its proper position; move that pan under a new filter. Loosen and take out old filters for organizing surfaces cleanly leaving no traces of other gaskets on it too as well as lubricating new ones using only clear internal combustion fluid instead so as positioning them by hand until being pushed against sealing surfaces after tightening slightly another three quarters round more or less then lower tools finally once again these back down below before taking such objects away entirely whenever everything else looks good enough not trying anything here anymore due its contact again since we're going down now anyway huh now let's start pouring fresh gas inside through any small door-like hole attached at top-right in order fill whole empty space around right hand corner plus operating motor briefly with choke open making ignition turned off but ready switch-on button pressed twice instead during cold season just case when starting first time otherwise checking sporadically after having had changed one's previous lot about new oillater on;. Check for leakages at the oil filter and drain plug, tighten if needed then re-checking its level again. After changing oil, check for any leaks or the oil levels. Finally, take it to a proper recycling plant when finished rather than pouring it in a river or flushing it in a toilet.

Genuine Subaru Legacy Oil Filter

Engine Oil filter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Oil Filters found

View related parts
Subaru Legacy Elem Complete Oil Filter
Part Number: 15208AA100
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaces: 15208AA023, 15208AA021, 15208AA080, 15208AA12A, 15208AA020, 15208AA024, 15208AA060, 15208AA09A, SOA6351520812, 15208AA022
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1990-2012 Subaru Legacy | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Base, 2.5i Limited, 2.5i Premium, Baja, Baja-B, Baja-S, Base, Brighton, Cold Weather, GT, GT Limited, L, L-S, Limited, LS, LS-D, LS-I, Out Back, Post, SUS, SUS Limited, Turbo, XT Limited | 2.2L H4, 2.2L H4 (New EVAPO), 2.2L H4 Series, 2.5L H4, 2.5L H4 SOHC, 2.5L H4 Turbo
View related parts
Subaru Legacy Oil Filter Complete
Part Number: 15208AA15A
$7.02 MSRP: $9.75
You Save: $2.73 (28%)
ADD TO CART
Product Specifications
- Other Name: Oil Filter
- Replaced by: 15208AA21A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2013-2021 Subaru Legacy | 2.4R F/R-O, 2.4R Limited, 2.4R Touring, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring | 2.4L H4 DIT, 2.5L H4, 2.5L H4 DI, 2.5L H4 DOHC
View related parts
Subaru Legacy Oil Filter
Part Number: 15208AA031
$9.18 MSRP: $12.75
You Save: $3.57 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaces: 15208AA030, SOA5165109
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2001-2019 Subaru Legacy | 3.0R, 3.0R Limited, 3.0R LL-Bean, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring, Flat6, Flat6 L.L.Bean, Flat6-S, SUS Flat6 | 3.0L H6, 3.6L H6
View related parts
Subaru Legacy Elem Complete Oil Filter
Part Number: 15208AA12A
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete; Oil Filter
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2009-2012 Subaru Legacy | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Base, 2.5i Limited, 2.5i Premium, Base, GT, GT Limited, XT Limited | 2.5L H4, 2.5L H4 SOHC, 2.5L H4 Turbo
View related parts
Subaru Legacy PT120103 Oil Filter
Part Number: 15208AA060
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1997-2005 Subaru Legacy | 2.5i, 2.5i Limited, Baja, Baja-S, Base, Brighton, Cold Weather, GT, L, Limited, LS, L-S, LS-I, Out Back, Post, SUS, SUS Limited | 2.2L H4 , 2.2L H4 (New EVAPO), 2.2L H4 Series, 2.5L H4
View related parts
Subaru Legacy PT120103 Oil Filter
Part Number: 15208AA024
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1997 Subaru Legacy | GT, LS-I, Out Back, SUS | 2.5L H4
View related parts
Subaru Legacy PT120103 Elem Complete Oil FILT
Part Number: 15208AA080
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2004-2005 Subaru Legacy | Baja-B, GT, GT Limited | 2.5L H4 Turbo
View related parts
Subaru Legacy Oil Filter 65MM
Part Number: 15208AA09A
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2006 Subaru Legacy | 2.5i, 2.5i Limited, GT, GT Limited | 2.5L H4, 2.5L H4 Turbo
View related parts
Subaru Legacy Oil Filter
Part Number: 15208AA023
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1994-1997 Subaru Legacy | Base, Brighton, GT, L, LS, LS-I, Out Back, Post, SUS, Turbo | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Legacy ELEM CP-OIL FLTR
Part Number: 15208AA21A
$7.02 MSRP: $9.75
You Save: $2.73 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 15208AA15A, 15208AA20A, 15208AA160, SOA6351520815
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2024-2025 Subaru Legacy | 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Subaru Legacy ELEM CP-OIL FLTR
Part Number: 15208AA20A
$7.02 MSRP: $9.75
You Save: $2.73 (28%)
ADD TO CART
Product Specifications
- Replaced by: 15208AA21A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2022-2023 Subaru Legacy | 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Subaru Legacy OIL FILTER COMPLETE
Part Number: SOA6351520815
$7.02 MSRP: $9.75
You Save: $2.73 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 15208AA21A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2022-2023 Subaru Legacy | 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Subaru Legacy Oil Filter
Part Number: 15208AA022
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1992-1994 Subaru Legacy | L, LS, Turbo
View related parts
Subaru Legacy Oil Filter
Part Number: 15208AA021
$6.64 MSRP: $9.22
You Save: $2.58 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Filter Complete
- Replaced by: 15208AA100
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1990-1992 Subaru Legacy | Base, L, LS, LS-D, Turbo

Subaru Legacy Oil Filter

The Legacy Oil Filter of the Subaru company minimizes the harmful effects of abrasive particles on the engine lubricant. This Oil Filter ensures that the moving parts are less affected by wear and tear, thus avoiding the addition of heat damage. Within its metal canister, pleated media made from cellulose and synthetic fibers, or a blend of materials, in this Oil Filter delivers oil at specified flow rates for thousands of miles while trapping dirt. The construction is suitable for Legacy engines that rely on steady pressure. Furthermore, the rigid walls are built to meet the original Subaru strength standards. Hence, they do not rupture at normal pump output. An efficiency level approaching 99 percent implies that the Oil Filter captures virtually all incoming contaminants, while valves internally assist in preserving pressure immediately after shutdown and during cold starts. Debris is held by adequate capacity until the next change to prevent sludge return to circulation. Regularly changing the Subaru Oil Filter before the media limits ensures the Legacy oil circuit remains unobstructed while preventing oil starvation. The Subaru Legacy engine always performs efficiently and lasts longer when cared for with this Oil Filter.

Our website stands as the go-to online destination for OEM Subaru Legacy Oil Filter. With complete lines of genuine Subaru Legacy Oil Filter available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Legacy Oil Filter Parts Questions & Experts Answers

Oil Filter
15208AA031
Q: How to Change the Engine Oil Filter on a Subaru Legacy?
A:
Oil changes should be regular if one is to care for the engine of his/her car because after a while, the oil in it becomes diluted and contaminated, causing premature wear out of the engine. When changing the oil filter and oil on your vehicle make sure that you have drain pan, rubber gloves, breaker bar/sockets and filter wrench available. You can also use rags or newspapers to wipe up spills. Hoist, ramps or jacks will allow you get under your car more easily. Find out where it is by draining some warm-up before removing an oil plug from an engine. In order to avoid getting a bad reading put the car on a level ground surface, heat up the engine and then remove the oil filler cap. Jack-up a vehicle with a floor jack; place drain pan beneath an oil plug; take off a plug; wait till all old oil has been drained out; check whether there are metal shavings in it; clean them away from an opening by wiping off all smudges remained there before reinstalling that plug carefully into its proper position; move that pan under a new filter. Loosen and take out old filters for organizing surfaces cleanly leaving no traces of other gaskets on it too as well as lubricating new ones using only clear internal combustion fluid instead so as positioning them by hand until being pushed against sealing surfaces after tightening slightly another three quarters round more or less then lower tools finally once again these back down below before taking such objects away entirely whenever everything else looks good enough not trying anything here anymore due its contact again since we're going down now anyway huh now let's start pouring fresh gas inside through any small door-like hole attached at top-right in order fill whole empty space around right hand corner plus operating motor briefly with choke open making ignition turned off but ready switch-on button pressed twice instead during cold season just case when starting first time otherwise checking sporadically after having had changed one's previous lot about new oillater on;. Check for leakages at the oil filter and drain plug, tighten if needed then re-checking its level again. After changing oil, check for any leaks or the oil levels. Finally, take it to a proper recycling plant when finished rather than pouring it in a river or flushing it in a toilet.